Wooster Skimcrete XL Easy Mix Leveling Compound for Treads and Nosings, 50 LB Drum

Wooster Skimcrete XL which is a fast drying, blended cement patch.This product is trowelable and adhesive friendly, having the lowest alkality of blended cement patches. Skimcrete XL is easy to work with on virtually any interior surface.

Directions for mixing are shown on the bucket.

50 Lb. Drum

Priced Per Piece- See Product details and specs in tabs below

See tabs below for additional information
    • SKU
      WSoo_Leveling Compound
    • Starting price: Price: $78.40 per item
     

    Wooster Leveling Compound Product Features and Benefits:

    • Long working time
    • Quick uniform drying time, regardless of thickness
    • No additives or primers for most uses
    • Featheredge to 5/8” thick – without aggregate
    • Non staining
    • Superior workability
    • Better coverage
    • Lowest alkalinity, adhesive friendly
    • Creamy, grit-free application
    • No dusting or cracking

    Physical Characteristics:

    • Working Time: 15-20 Minutes
    • Setting Time: 30 Minutes
    • Covering Time: 30-75 Minutes
    • Ph: <10
    • Compressive Strenght:4000+ psi (28 MPa)
    • Flexural Strenght: 1300+ psi (9 MPa)
    • Tensile Strenght: 500 psi (3 MPa)
    • Thickness: Featheredge to 5/8" (16 mm) (neat)
    • Coverage - in square feet per 100 Lbs. (Note: Product comes in 50 Lb. Drum)

    Table for Wooster Skimcrete Coverage

    Limtations:

    • Where hydrostatic pressure (water) exists or moisture emissions exceed level permited for installing floorcovering
    • Where surface or ambient tempeture falls to or below 50°F within 72 hours of installation
    • Over presswood, particle board, masonite, chipboard, OSB, underlayment board not of APA underlayment (exterior) grade or similar dimenionally unstable materials susceptible to movement or swelling
    • Over gypsum based patched or underlayment material due to chemical reaction
    • Single layer stripwood floors 

    Uses:

    Use to smooth or cover cracks, joints, or other imperfections in concrete, wood, or adhesive residue. Also used in construction to help level floors prior to the installation of nosings and treads on stairs.

    Mixing: 

    Add 2.5 to 3 Parts SKIMCRETE to 1 part cool water, Use clean containers and mixing implements. Mix thoroghly to a lump-free trowelable consistency. Mixture will remain workable for 15-20 minutes.

    This product has a 2 year warranty against defects in material and workmanship.

    Click here to view our Full Warranty Policy.

    See our Heavy Duty Construction Adhesive that is helpful when laying stair nosings on pre-existing concrete steps.

     

      • SKU
        WSoo_Leveling Compound
    • QuickShip
      No
    • Manufacturer
      Wooster Products, Inc

    Click to Print Product Specs

    Wooster Leveling Compound for evening steps in preparation for laying treads and nosings, 50 lbs. Drum

     

    Suface Preparation: All supporting surfaces shall be structurally sound, solid, free of movement and well bonded. Ensure underlying surface is free of excess moisture and clean of any contaminants such as dirt, wax, oil, paint, curing compounds, sealers, solvent, oil products or any gypsum materials or foreign matter that may interfere with a proper bond. When a proper bond is questionable, perform a test patch in an inconspicuous area. DO NOT PROCEED if dissatisfied with bond and contact DEPENDABLE’s Technical Services.

    Concrete Floors: Remove all foreign matter by mechanical means. Floor must be free of efflorescence and excess moisture. To correct moisture problems, including lack of proper under slab vapor barrier, see DEPENDABLE’s moisture protection products.

    Wood Floors: Ensure wood floors are free of movement and excessive moisture. Fasten any loose boards. Stripwood floors should be covered with underlayment grade quality board.

    Underlayment Board Joints: To avoid “peaking,” do not butt sheets tightly. Leave a space the thickness of a matchbook cover (approx. 1/32”) between sheets. The installer may wish to seal the joints, hammer-indents and other “raw” spots with an appropriate brush coat of DEPENDABLE LATEX. This will keep the moisture in SKIMCRETE XL and/or the adhesive from being drawn into the board, which may cause swelling and/or delamination.

    Existing Ceramic Tile, Quarry Tile, etc.: (Not Vinyl–VCT & VAT) Must be well bonded. The surface must be clean and free of waxes and contaminants that might inhibit bonding. For best bond, prime with Acrylic Embossing Additive. Once primed, allow AREA to nearly dry and become tacky before covering with SKIMCRETE XL.

    Metal & Other Types of Flooring: Remove any rust or contaminants. Wash and allow to dry completely. Prime with DEPENDABLE ACRYLIC EMBOSSING ADDITIVE. Allow to nearly dry and become tacky. (This includes metal, epoxy and terazzo)

    Vinyl Floors: Existing resilient floors shall be single layer, fully adhered and well bonded. Thoroughly clean all foreign matter such as dirt, grease, oil, wax or any other contaminates which may inhibit bond. While floor is wet, use a cleaning pad and remove any remaining wax or dirt, while scuffing the surface. Rinse thoroughly with clean water and allow to dry. New wear layers being sold can be difficult to bond to. While some wear layers may be bonded to with just a thorough cleaning, others may re- quire abrading and/or priming the surface with DEPENDABLE ACRYLIC EMBOSSING ADDITIVE. ACRYLIC EMBOSSING ADDITIVE must be added to the powdered product to increase bonding characteristics. The installer is advised to always perform a test patch area over resilient goods to assure acceptable bond.

    Adhesive Residue: Using mechanical means, remove loose, brittle or thick/heavy accumulations to a well-bonded residue. Sweep or vacuum area. Prime residue with DEPENDABLE ACRYLIC EMBOSSING ADDITIVE and allow to become nearly dry and tacky. Caution: Cutback adhesive may contain asbestos. Contact state or local authorities for proper removal and disposal procedures.

    MIXING: Mix SKIMCRETE XL with cool clean water or DEPENDABLE latex additives for every 10 lbs use 1.5 quarts or 4 quarts for every 25 lbs. Use clean containers and mixing implements, as leftover residue can accelerate set and/or reduce pot life of new mix. Mix thoroughly to a lump-free trowelable consistency. Mixture will remain workable for approximately 15 minutes. Mix only what can be used in that time. Do not attempt to extend pot life by later adding water. Do not mix directly on floor. Use felt, scrap vinyl or mixing bucket. Over vinyl floors or whenever a primer is necessary use ACRYLIC EMBOSSING ADDITIVE must be used in place of water.

    APPLICATION: Using a smooth flat trowel, force SKIMCRETE XL into joints, cracks holes and deeper fills bearing down on the trowel. Smooth the surface to a thin covering over the prepared substrate. Build any thicker fills or transitions to 5/8” thick. Deeper fills may be achieved with multiple lifts. Always allow prior lift to dry completely. When dry, sand or scrape smooth for a perfect finish. Vinyl & Metal Floors — When using SKIMCRETE XL as an embossing leveler, mix approximately 2.5-3 parts SKIMCRETE XL into 1 part ACRYLIC EMBOSSING ADDITIVE. Mix to a lump free trowelable mix. Apply using a flat smooth steel trowel drawing material across the pattern to be filled at angles to the pattern to ensure an even and complete fill. Allow to dry completely, at least two (2) hours before covering.

    LIMITATIONS - Do not use...  

    • Where hydrostatic pressure (water) exists or moisture emissions exceed level permitted for installing floor covering.
    • Where surface or ambient temperature falls to or below 50°F within 72 hours of installation
    • Over presswood, particle board, masonite, chipboard, OSB, underlayment board not of APA Underlayment (exterior) grade or similar dimensionally unstable materials susceptible to movement or swelling.
    • Over gypsum based patches or underlayment material due to chemical reaction.
    •  Single layer stripwood floors.

    SHIPPING / PROCESSING TIME:


    This product ships directly from the manufacturer. 
    Please allow 1 - 3 weeks to ship

    Expedited processing is available, please contact us for assistance

     

    • Domestic Shipping Fees- (Hawaii and Alaska not Included):
      • FREE SHIPPING on orders over $200.00 (excludes oversized and freight orders). 
      • There will be a flat $19.99 shipping and handling fee on orders under $300.00.
      • Oversize: Orders containing items sized 50" - 95" have an oversize surcharge of $49.99.
      • Freight Items: Orders containing items sized 96" - 108" have an oversize surcharge of $199.99.
      • Oversize Freight Items: Orders containing items sized 109" and above have an oversize surcharge of $299.99.
      • Orders totals above $2,000.00 will ship free, regardless of size.
         
    • Alaska and Hawaii, Canada, and International Shipping:
    • Returns:
      • These items are custom made and not returnable.
      • CLAIMS FOR SHORTAGE OR DAMAGE IN TRANSIT: All claims must be made within Seven (7) days of receipt of goods.