Pemko #S771x6 Adhesive Weatherstrip, 1" Silicone Seal with 6 Fins, .313" Profile, Black Silicone

This six-fin weatherstrip gasketing slows and prohibits smoke, fire, weather, sound and dirt from infiltrating a room. It is easily installed with a self-adhesives backing along the perimeter of the door or at the gap between a set of double doors. The seal is made of high quality silicone which can withstand temperature extremes.

SOLD IN PRECUT STRIPS

See tabs below for additional information

Quantity

Add to compare

This Six Fin Self-Adhesive Silicone Weatherstrip is designed to be applied to the full perimeter of door or between a pair of double doors, to seal the gaps present. The six fin design is particularly effective in blocking sound and light from infiltrating, great for hotels and dormitory condos. It is easily applied with a self-adhesive backing to reduce infiltration of smoke, fire, weather, sound and dirt. It also provides protection from weather conditions and minimizes heat loss.

Silicone Rubber: This silicone door gasket is extruded from high temperature silicone rubber, which is effective between -76°F and 446°F, making it ideal for an exterior door. It is self-extinguishing, non-toxic, is unaffected by ozone, ultraviolet rays and sunlight and is impervious to mildew and fungus.

Dimensions: The base of the seal has a width of 1" while the fins extends upward starting at to a total height of .313" (5/16"). It begins compressing at .313" (5/16") and compresses to seal gaps as small as .0625" (1/16").

Installation: The gasket is easily installed with a high quality self-adhesive backing. Please note, this product has a limited shelf life. Product must be used within 6 months of purchase and must be stored between 50°F and 100°F.

Please note, images are for illustrative purposes only. They are not actual photos. Therefore, actual colors may vary slightly and size may be enlarged to show detail. See product specs for exact measurements.

This product has a 5 year guarantee against defects in material and workmanship.
Click to view our Full Warranty Policy.

For smaller gaps, consider our .5" Angled T Shaped Silicone Weatherstrip.

- SKU
  PKS771x6BL-7
QuickShip
No
Manufacturer
Pemko Manufacturing
MPN
S771x6
Size
7', 8', 9', 10'
About This Product
- Seal Type
  Silicone
- Door Type
  Double Active Doors, Single Door
- Temperature Range
  -76°F to 446°F
Dimensions
- Seal Height
  1"
- Width
  5/16"
Finishes
- Finish
  Black
Compliance Details
- Compliance Details
  Air Infiltration Rated, Smoke Rated, Fire Rated, BHMA Certified, GreenGuard Gold Certified, Sound Rated
- ANSI Designation
  R0E154, R0E155
- Warranty
  5 Year Limited Warranty

Click to Print

Sample Application

Click to Print Installation Tips

Installation Tips:

All adhesive gaskets have a limited shelf life. These products must be used within 6 months of purchase and must be stored between 50ºF and 100ºF.
Thoroughly clean the frame with the enclosed cleansing towelette to remove grease, dust or cleanser build-up. Before installation, wait for frame surface to completely dry (evaporate). Some hospital environments have wax or anti-bacterial cleanser build-up. As an alternative or substitute cleanser, use isopropyl (rubbing) alcohol. Note: Mineral spirits or other petroleum based cleaning products should NOT be used.
If frames are too cold (below 50ºF) or too hot (above 100ºF) adhesion may be impaired.
Installation should take place after construction is completed, flooring is installed and final cleaning is completed.
Paint on frame must be cured for at least 5-7 days. Paint cannot be wet under dry surface when gaskets are pressed on. Avoid quick-dry primers, which leave a powdery surface preventing sufficient adhesion. When applying to a wood frame, the surface must be non-porous and sealed. Follow standard industry guidelines on sealed wood frames and/or rough surface before applying. Note: Anti-bacterial, anti-fungal or silicone additives in paint may inhibit adhesion.
Do NOT stretch material. Product can retract or shrink if stretched.
Use very firm, perpendicular pressure when applying. Use wallpaper seam roller to reinforce adhesion after applying.
Do not stretch material when using seam roller. Run roller with up and down motions.
Double check adhesion after 2-3 hours before leaving job overnight.
If gaskets separate from the frame, press again with firm pressure in place. If adhesive strip is exposed, airborne dust may impede adhesion. Replacement may be necessary.
Application at header can be awkward due to overhead condition. Be sure to apply enough pressure.
Adhesion takes delayed set. Immediate removal and resetting can be done if error occurs in initial placement. DO NOT reset after one hour. Full set is reached in 24 hours.

Click to View Ratings Explained

SHIPPING / PROCESSING TIME:

This product ships directly from the manufacturer.

Please allow 2 - 3 weeks to ship

Domestic Shipping Fees- (Hawaii and Alaska not Included):
- FREE SHIPPING on orders over $300.00 (excludes oversized and freight orders).
- There will be a flat $19.99 shipping and handling fee on orders under $300.00.
- Oversize: Orders containing items sized 50" - 95" have an oversize surcharge of $49.99.
- Freight Items: Orders containing items sized 96" - 108" have an oversize surcharge of $199.00.
- Oversize Freight Items: Orders containing items sized 109" and above have an oversize surcharge of $299.99.
- Orders totals above $2,000.00 will ship free, regardless of size.
Alaska and Hawaii, Canada, and International Shipping:
- Please see our Shipping Information page for details.
Returns:
- This product is custom made and is not returnable.
- We are committed to your satisfaction, as a courtesy, we may, at our discretion accept returns with a minimum 35% restock fee.
- CLAIMS FOR SHORTAGE OR DAMAGE IN TRANSIT: All claims must be made within Seven (7) days of receipt of goods.
- Weatherstripping products will not be considered for returns.
- Item must be in new, re-saleable condition.
- Please call or email us to receive an RMA number before returning. No returns will be processed without an RMA number.
- Return shipping is customer's responsibility. A return address will be provided with RMA#.
- If you are shipping via USPS (not recommended) do NOT require signature as we will not be able to pick up your package from local post office facility.