Pemko #S771x6 Adhesive Weatherstrip, 1" Silicone Seal with 6 Fins, .313" Profile, Black Silicone
This six-fin weatherstrip gasketing slows and prohibits smoke, fire, weather, sound and dirt from infiltrating a room. It is easily installed with a self-adhesives backing along the perimeter of the door or at the gap between a set of double doors. The seal is made of high quality silicone which can withstand temperature extremes.
SOLD IN PRECUT STRIPS
This Six Fin Self-Adhesive Silicone Weatherstrip is designed to be applied to the full perimeter of door or between a pair of double doors, to seal the gaps present. The six fin design is particularly effective in blocking sound and light from infiltrating, great for hotels and dormitory condos. It is easily applied with a self-adhesive backing to reduce infiltration of smoke, fire, weather, sound and dirt. It also provides protection from weather conditions and minimizes heat loss.
Silicone Rubber: This silicone door gasket is extruded from high temperature silicone rubber, which is effective between -76°F and 446°F, making it ideal for an exterior door. It is self-extinguishing, non-toxic, is unaffected by ozone, ultraviolet rays and sunlight and is impervious to mildew and fungus.
Dimensions: The base of the seal has a width of 1" while the fins extends upward starting at to a total height of .313" (5/16"). It begins compressing at .313" (5/16") and compresses to seal gaps as small as .0625" (1/16").
Installation: The gasket is easily installed with a high quality self-adhesive backing. Please note, this product has a limited shelf life. Product must be used within 6 months of purchase and must be stored between 50°F and 100°F.
Please note, images are for illustrative purposes only. They are not actual photos. Therefore, actual colors may vary slightly and size may be enlarged to show detail. See product specs for exact measurements.
This product has a 5 year guarantee against defects in material and workmanship.
Click to view our Full Warranty Policy.
For smaller gaps, consider our .5" Angled T Shaped Silicone Weatherstrip.
-
QuickShipNo
-
ManufacturerPemko Manufacturing
-
MPNS771x6
-
Size7', 8', 9', 10'
- About This Product
-
Seal TypeSilicone
-
Door TypeDouble Active Doors, Single Door
-
Temperature Range-76°F to 446°F
-
- Dimensions
-
Seal Height1"
-
Width5/16"
-
- Finishes
-
FinishBlack
-
- Compliance Details
-
Compliance DetailsAir Infiltration Rated, Smoke Rated, Fire Rated, BHMA Certified, GreenGuard Gold Certified, Sound Rated
-
ANSI DesignationR0E154, R0E155
-
Warranty5 Year Limited Warranty
-
Click to Print Installation Tips
Installation Tips:
- All adhesive gaskets have a limited shelf life. These products must be used within 6 months of purchase and must be stored between 50ºF and 100ºF.
- Thoroughly clean the frame with the enclosed cleansing towelette to remove grease, dust or cleanser build-up. Before installation, wait for frame surface to completely dry (evaporate). Some hospital environments have wax or anti-bacterial cleanser build-up. As an alternative or substitute cleanser, use isopropyl (rubbing) alcohol. Note: Mineral spirits or other petroleum based cleaning products should NOT be used.
- If frames are too cold (below 50ºF) or too hot (above 100ºF) adhesion may be impaired.
- Installation should take place after construction is completed, flooring is installed and final cleaning is completed.
- Paint on frame must be cured for at least 5-7 days. Paint cannot be wet under dry surface when gaskets are pressed on. Avoid quick-dry primers, which leave a powdery surface preventing sufficient adhesion. When applying to a wood frame, the surface must be non-porous and sealed. Follow standard industry guidelines on sealed wood frames and/or rough surface before applying. Note: Anti-bacterial, anti-fungal or silicone additives in paint may inhibit adhesion.
- Do NOT stretch material. Product can retract or shrink if stretched.
- Use very firm, perpendicular pressure when applying. Use wallpaper seam roller to reinforce adhesion after applying.
- Do not stretch material when using seam roller. Run roller with up and down motions.
- Double check adhesion after 2-3 hours before leaving job overnight.
- If gaskets separate from the frame, press again with firm pressure in place. If adhesive strip is exposed, airborne dust may impede adhesion. Replacement may be necessary.
- Application at header can be awkward due to overhead condition. Be sure to apply enough pressure.
- Adhesion takes delayed set. Immediate removal and resetting can be done if error occurs in initial placement. DO NOT reset after one hour. Full set is reached in 24 hours.