Hager 790-906 Continuous Hinge, Half Mortised With Edge Guard
Hager 790-906 is a Heavy-Duty, Half Mortised Stainless Steel Continuous Barrel Hinge which is mortised to the door edge and surface of the door frame. Designed with a door edge protection lip for doors 1 3/4" thick and up to 600 pounds. Compatible with doors of any material and is available in a choice of lengths and finishes.
PRICED PER PIECE - See full product details and specs in the tabs below
Hager 790-906 Continuous Barrel Type, Stainless Steel Half Mortised Leaf Hinge for 1 3/4" doors by Hager companies.
- Available in five sizes: (chart) For 119" Length, please contact us or call 845-388-1200 as Freight Shipping Charges may apply.
- Security and Privacy: Eliminates the gap between the frame and door so doors cannot be pried open, offers privacy on hospital and toilet partitions.
- Finish: Stainless steel continuous hinges are brushed to a satin finish (US32D). For custom color painted or powder coated finishes please contact our office at 845-388-1200 or contact us (Color samples are required for matching.)
- Materials: Constructed from 14 Gauge Type 304 Stainless Steel with lubricated nylon 6/6 bearings between each knuckle and stainless steel pin. 1/4" diameter Stainless Steel Pin.
- Features: Heavy-duty construction to support doors up to 600 pounds. Energy saving, creates a seal from the top to bottom of the door to prevent air infiltration and permanent weather barrier.
- Design: Half mortised leaf edge mount hinge for 1 3/4" thick door with security molding. Protective corner guard with door edge protection lip (see Product Data Tab.)
- Fasteners: #10-24 X 5/8" S/S Dril-Kwik (R) (metal frame)
#1/4-20 X 3/4" 2C Dril-Kwik (R) (metal door)
#1/4-14 X 1 2C Type AB (wood frame)
- Applications: May be used for all door types. Not recommended for doors with a beveled edge on the hinge side. Corrosion resistant for swimming pool buildings, sewage, water treatment plants and salt spray environment. Ideal for applications where doors and frames are subjected to severe abuse such as hospitals and institutions.
- Clearance: Minimum clearance between the hinge edge of the door and the frame is 1/8" plus standard lockside clearance.
- Reinforcement: No door reinforcement required. No frame reinforcement required up to 200 lbs. Heavier weight use 16-gauge channel.
- Fire-Rating: Up to 3 hour metal and 90 min. wood composite (with studs).
- Certification: ANSI A156.26 Grade 1 for 150 pound doors.
- Additional Options: Including security studs, specialty fasteners, hospital tip and customize hole patterns may be ordered, for details and pricing please contact us or call our office at 845-388-1300.
- Installation: Installed either with or without reinforcements depending on door weight. Installation screws are provided (see Installation Tab.) The frame face must have a flat surface at least 1 5/8" wide. Note: Model 790-906 features an integral protective guard and is not recommended for doors with a beveled edge on the hinge side.
- Priced per piece
- Please note, images are for illustrative purposes only. They are not actual photos. Therefore, actual colors may vary slightly and size may be enlarged to show detail. See product specs for exact measurements.
Click here to view our Hager 790-909 Continuous Hinge, Stainless Steel Full Surface Swing Clear.
This product has a lifetime warranty against defects in workmanship and material.
Click here to view our Full Warranty Policy.
Printable Documents: |
Click to print Hager 790-906 Continuous Hinge 79" Template. Click to print Hager 790-906 Continuous Hinge 83" Template. Click to print Hager 790-906 Continuous Hinge 85" Template. Click to print Hager 790-906 Continuous Hinge 95" Template. Click to print Hager 790-906 Continuous Hinge 119" Template. Click to print Hager Continuous Hinge Electric Modification Information. |
Product Specs: |
![]() |
Standard Locations for Electrical Modification: |
Click to print Installation Instructions for Hager 790-904 Stainless Steel Continuous Hinge. |
Hager Models 790-904 and 790-906 are Stainless Steel Continuous Half Edge Mount Hinges for 1 3/4" thick doors. The frame face must have a flat surface at least 1 5/8" wide. Clearance required between the hinge edge of the door and the frame rabbet is 1/8" minimum. Model 790-906 features an integral protective corner guard and is not recommended for use on doors that have a beveled edge on the hinge side. |
Hinge Length: |
All Hager Stainless Steel Continuous Hinges are supplied 7/8" to 1" shorter than the nominal door height to avoid threshold or carpet clearance problems. If the hinge must be trimmed shorter, first determine the correct hand of the door and orientation of the hinge. Remove the bottom pin cap and trim from the bottom end of the hinge only to achieve the desired length - do not cut the top end. Undercut the pin 7/8"shorter for clearance and reinsert the bottom pin cap. |
General Fitting Procedure: |
|
Door Preparation: |
1. With the hinge open, place the hinge door leaf against the edge of the door. Position the top of the hinge flush with the top of the door. For the 790-904, to achieve a 1/8" inset, position the 'pull' face of the door 5/8" from the center of the hinge pin. For the 790-906, position the integral corner guard fully against the 'push' face of the door. 2. Mark and center punch the screw hole locations. Accurate location is important for proper hinge installation. 3. For metal doors 14 gauge or less, it is not necessary to pre-drill pilot holes if using the #10 self-driling screws provided. For metal doors 12 gauge and over, drill and tap all mounting holes for #10-24 threads prior to installing the screws. For wood doors, pre-drill pilot holes using a #25 bit. 4. Attach the hinge to the door. For metal doors, use the #10 self-drilling screws provided (recommended driver speed 1,900-2,500 RPM). For wood doors, use the #10 wood screws provided. |
Hanging the Door: |
1. With the hinge mounted to the door, set the door into the frame using shims or wedges to adjust for the desired clearance on all sides. Allow 1/8" clearance between the top of the door and the frame header rabbet. Allow 1/16" minimum clearance between the hinge door leaf and the frame rabbet. 2. With the door held securely in place, rotate the hinge leaf into position on the face of the frame. a. For metal frames, mark and center punch the hole locations on the frame face. For metal frames, 12 gauge or less it is not necessary to pre-drill pilot holes if using the 1/4" self-drilling screws provided. For thicker metal frames, pre-drill pilot holes using a 7/32" bit. Install the 1/4" self-drilling screws (recommended driver speed 1,900-2,500 RPM), placing a Molding Clip under the head of a screw at five locations along the hinge - one at each end and the others spaced equally in between. b. For wood frames, mark and center punch the hole locations on the frame face. Pre-drill pilot holes using a 7/32" bit. Install the #14 wood screws, placing a Molding Clip under the head of a screw at five locations along the hinge - one at each end and the others spaced equally in between. 3. Remove all shims and wedges and make a gentle trial swing. Carefully check the door for proper swing and clearance. |
Install the Snap-On Molding: |
1. Position the Molding so that the short leg is closest to the hinge pin. Hook the short leg over the Molding Clips along the full length of the hinge. Starting at the top and working downward press the long leg of the Molding in place completely over the outside edge of the door leaf. If necessary, gently tap in place using a rubber mallet, taking care not to damage the molding. |